Confirm split-phase service
Rated output is 120/240Vac with an L1+L2+N+PE connection.
Do not treat it as single phaseUS series · 120/240Vac split-phase inverter
ELE GES4862M120-500Split-phase output with 9kW of PV input.
Documented for 120/240Vac L1+L2+N+PE systems with a 48V battery platform, one 27A MPPT channel and AC coupling. Parallel operation is not supported.
US seriesSplit-phase48V batteryNo parallel
AC output120/240VSplit-phase L1+L2+N+PE
PV input9kWOne 27A MPPT channel
Family visual · confirm image and current document revision for the exact supplied unit
6200WRated output table value
4800WSame-phase output
9300VAPeak per phase
NoParallel operation
Selection answer
A dedicated 120/240Vac architecture, not a 120Vac substitute.
The model fits a documented split-phase branch using L1, L2, neutral and protective earth. The brochure publishes separate per-phase and same-phase output values, so load balance must be checked from the current datasheet rather than inferred from the model name.
Use both output rows
The table lists 6200W per phase and 4800W for same-phase output.
Verify load-balance rulesKeep PV inside 500V
Maximum DC input is 9kW through one 27A MPPT channel.
MPPT operates at 90-450VDo not design a parallel bank
Parallel units are explicitly listed as not supported for this model.
Select another documented modelDocumented operating paths
PV and battery coordinated across L1, L2 and neutral.
The brochure lists AC coupling, CT anti-backflow, on-grid, off-grid and battery-less operation. Final conductor sizing, neutral behavior, protection and load allocation must follow current documentation.
System overviewELE GES4862M120-500
01 / Solar input
PV array
90-500V input range
One 27A MPPT channel
PV → inverter
02 / Energy conversion
Split-phase inverter
ELE GES4862M120-500
9300VA peak per phase
Family visual · exact unit may vary03 / Energy storage
48V battery
120A max charge
140A max discharge
Battery ↔ inverter
04 / AC connection
Split-phase loads
120/240Vac output
L1+L2+N+PE
Inverter → load interfaces
Functional overview, not an installation wiring diagram. Follow the model-specific manual for terminal assignments and protection.
Model specification
Published values tied to ELE GES4862M120-500.
Values below are transcribed from the supplied July 2026 neutral brochure. Confirm the latest model revision before PV design, battery integration, split-phase load allocation or installation.
01
DC input / PV
- Maximum DC input power
- 9000W
- Maximum DC input voltage
- 500V
- Start voltage
- 120V
- PV input voltage range
- 90-500V
- MPPT voltage range
- 90-450V
- MPPT channels
- 1
- Maximum MPPT input current
- 27A
- Maximum PV charging current
- 120A
02
AC input and output
- Per-phase AC input range
- 85-140Vac
- Input frequency range
- 47-55Hz / 57-65Hz
- Maximum per-phase input current
- 40Aac
- Maximum AC charge current
- 100Adc
- Rated output power (per phase)
- 6200W
- Rated output (same phase)
- 4800W
- Peak power (per phase)
- 9300VA
- Rated output voltage
- 120/240Vac
- Output frequency
- 50/60Hz
- Power factor
- 1
- Connection
- L1+L2+N+PE
03
Battery parameters
- Rated battery voltage
- 51.2V
- Minimum start voltage
- 44V
- Battery voltage range
- 40-60Vdc
- Battery type
- Lead-acid / lithium
- Maximum charge / discharge
- 120A / 140A
- Charge voltage range
- 40-60Vdc
- Battery-less operation
- Yes
- PV / grid battery activation
- Listed feature
04
General data
- Dimensions (W × D × H)
- 420 × 330 × 122mm
- Weight
- 12kg
- Operating temperature
- -10°C to 55°C
- Derating
- Above 45°C
- Storage temperature
- -25°C to 60°C
- Humidity range
- 5%-95%
- Cooling
- Forced air, variable speed
- Protection class / noise
- IP21 / ≤60dB
05
Protection and transfer
- Grid overload protection
- Circuit breaker
- Grid breaker rating
- 40A
- AC reverse feed protection
- Yes
- Charge short-circuit protection
- Fuse
- AC output short-circuit protection
- Yes
- Wiring protection
- Yes
- Transfer time
- 10ms typical
- CT anti-backflow
- Yes
06
Interfaces and limits
- Communication ports
- USB / RS485 / Wi-Fi / CAN
- AC coupling
- Yes
- Dry contact control
- Yes
- Remote diagnostics / OTA
- Yes
- Parallel units
- Not supported
- Maximum altitude
- 4000m
- No-derating altitude
- ≤2000m
- Maximum efficiency
- >92.5% battery to load
- Phases
- Split-phase
Brochure-listed functions
Split-phase capability with explicit output boundaries.
These functions are listed on the supplied model page. Availability, firmware behavior, accessories and configuration should be checked against the current supplied package.
Check project compatibility →120/240Vac split-phase output
The table lists L1+L2+N+PE, 6200W rated output per phase and 4800W same-phase output. Confirm load allocation rules.
AC coupling and CT anti-backflow
Both functions are listed. Confirm CT selection, placement, source coordination and commissioning method.
Single 27A / 9000W PV channel
PV open-circuit voltage must remain below 500V and operating voltage inside the 90-450V MPPT range.
9300VA peak per phase
The brochure describes a 150% surge peak for 5 seconds. Verify the actual phase load and starting profile.
Generator and battery-less modes
Dry-contact generator control and PV plus grid direct supply are listed; confirm project behavior before design.
Before specification
Do not infer total output from one table row.
The brochure publishes per-phase and same-phase values without an independent combined-rating explanation. Preserve those labels and obtain the current load-balance documentation before design.
Split-phase loads
Document L1, L2, 240V and neutral loads separately, including continuous and starting demand.
PV string Voc
Calculate cold-weather open-circuit voltage and keep it within the documented maximum.
Battery and BMS
Confirm model, 40-60Vdc window, 120A/140A current, CAN/RS485 protocol and cable pinout.
No parallel operation
The model is explicitly listed as not supporting parallel units; do not plan multi-unit expansion.
Documents
Request the current datasheet, manual and applicable certificate scope for the target market.
Certification note
The brochure specification table references UL 1741, CSA C22.2 No. 107.1 and FCC Part 15 Class B. This website does not present those references as independently verified certificates. Request the applicable certificate, exact model scope and revision before relying on a compliance claim.
Model FAQ
Answers tied to ELE GES4862M120-500.
The supplied model page controls the answers below. Project suitability still depends on the complete split-phase, PV, battery and protection design.
Yes. The brochure lists 120/240Vac output, split-phase operation and an L1+L2+N+PE connection.
The table labels 6200W as rated output per phase and 4800W as same-phase output. This page does not calculate an unstated combined rating.
No. Parallel units are listed as not supported. Choose a documented parallel-capable split-phase model if expansion is required.
The brochure lists 9000W maximum DC input, one 27A MPPT channel, a 48V battery platform and 120A/140A maximum charge/discharge current.
Send the destination country, split-phase service, L1/L2 load schedule, PV strings, battery and required documents through the inquiry form.
Model-specific inquiry
Send the L1 and L2 load schedule.
Include country, 120V and 240V loads, neutral requirements, PV strings, battery model, quantity and required documents. The inquiry form will prefill this model number.
Request ELE GES4862M120-500 data →